HP Hewlett Packard Network Cables 04H8095 User Manual

Auto LANstreamer PCI Adapter  
04H8095  
Installation Guide  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
1 Connecting to a Netware 3.12 Server  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95  
• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and  
NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 Boot the machine to a DOS prompt, and Netware client for DOS and MS-  
Windows disk 1.  
6 Execute INSTALL.EXE and set lines 1-5 as listed below;  
• C:\NWCLIENT  
• YES  
• YES  
C:\WINDOWS  
• NO  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
• IBM Auto LANStreamer PCI Adapter (use the driver on disk 3 of 5, Net-  
ware DOS requester Installation disk)  
7 Highlight option 6 to continue with installation.  
8 When prompted, insert the corresponding disks to complete file transfer  
and driver installation.  
9 When the install utility is finished, press <CRTL><ALT><DEL> to restart  
the machine.  
10 After windows loads, open the “NETWORK” folder, and double-click the  
“NETWORK SETUP” icon.  
11 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0  
and above)” is selected under “Install Windows support for the following  
network only:”  
12 Click on “OK” twice and the installation is complete.  
 
1 Connecting to Netware 3.12 Server  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: Windows 95 Default  
• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and  
NWLink NetBIOS transfer protocols.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 Upon booting, Windows 95 will automatically recognize the adapter. Click  
on “Next.”  
6 When prompted, click on “Other Locations.”  
7 Insert drivers disk 4 of 6 (Auto LANStreamer PCI NDIS 3.0 Driver  
Diskette), set the path to “A:\” and click “OK.” (If you have an HP  
preloaded HDD, set the path to “C:\LANDRV\LNSTRM\DISK4\”)  
8 Verify that “IBM Auto LANStreamer PCI Adapter (NDIS3)” is listed and  
click on “Finish.”  
9 When prompted to insert disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
10 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\” and click “OK.” (If you have an HP preloaded HDD, set the path  
to “C:\LANDRV\LNSTRM\DISK2\”)  
11 At the “Copying Files” window, click on “OK.”  
 
1 Connecting to Netware 3.12 Server  
Windows 95 SR2  
12 Click “OK” to provide your Computer and Workgroup names.  
13 Enter your Computer Name, Workgroup Name, Computer Description,  
and click on “Close.”  
14 Accept the default properties, and click on “OK.”  
15 When prompted to insert the Windows 95 CD-ROM, click on “OK.”  
16 Set the path to your Windows 95 files and click on “OK.” (If you have an  
HP pre-loaded HDD, set the path statement  
C:\MASTERS\WIN95\SYSTEM\CABS\”).  
17 When prompted to insert the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
18 Insert disk 4 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\Win95\” and click “OK.” (If you have an HP preloaded HDD, set the  
path to “C:\LANDRV\LNSTRM\DISK4\WIN95\”)  
19 Click on “Yes” to restart your computer and finish the installation.  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
2 Connecting to a Netware 4.11 Server  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95  
• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 Boot the machine to a DOS prompt, and Netware client for DOS and MS-  
Windows disk 1.  
6 Execute INSTALL.EXE and set lines 1-5 as listed below;  
• C:\NWCLIENT  
• YES  
• YES  
C:\WINDOWS  
• NO  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
• IBM Auto LANStreamer PCI Adapter (use the driver on disk 3 of 5, Net-  
ware DOS requester Installation disk)  
7 Highlight option 6 to continue with installation.  
8 When prompted, insert the corresponding disks to complete file transfer  
and driver installation.  
9 When the install utility is finished, press <CRTL><ALT><DEL> to restart  
the machine.  
10 After windows loads, open the “NETWORK” folder, and double-click the  
“NETWORK SETUP” icon.  
11 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0  
and above)” is selected under “Install Windows support for the following  
network only:”  
12 Click on “OK” twice and the installation is complete.  
 
2 Connecting to a Netware 4.11 Server  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: Windows 95 Default  
• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 Upon booting, Windows 95 will automatically recognize the adapter. Click  
on “Next.”  
6 When prompted, click on “Other Locations.”  
7 Insert drivers disk 4 of 6 (Auto LANStreamer PCI NDIS 3.0 Driver  
Diskette), set the path to “A:\” and click “OK.” (If you have an HP  
preloaded HDD, set the path to “C:\LANDRV\LNSTRM\DISK4\”)  
8 Verify that “IBM Auto LANStreamer PCI Adapter (NDIS3)” is listed and  
click on “Finish.”  
9 When prompted to insert disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
10 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\” and click “OK.” (If you have an HP preloaded HDD, set the path  
to “C:\LANDRV\LNSTRM\DISK2\”)  
11 At the “Copying Files” window, click on “OK.”  
 
2 Connecting to a Netware 4.11 Server  
Windows 95 SR2  
12 Click “OK” to provide your Computer and Workgroup names.  
13 Enter your Computer Name, Workgroup Name, Computer Description,  
and click on “Close.”  
14 Accept the default properties, and click on “OK.”  
15 When prompted to insert the Windows 95 CD-ROM, click on “OK.”  
16 Set the path to your Windows 95 files and click on “OK.” (If you have an  
HP pre-loaded HDD, set the path statement  
C:\MASTERS\WIN95\SYSTEM\CABS\”).  
17 When prompted to insert the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
18 Insert disk 4 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\Win95\” and click “OK.” (If you have an HP preloaded HDD, set the  
path to “C:\LANDRV\LNSTRM\DISK4\Win95\”)  
19 Click on “Yes” to restart your computer and finish the installation.  
 
3 Connecting to a Windows NT 3.51 Server  
Windows for Workgroups  
3 Connecting to a Windows NT 3.51 Server  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95  
• Microsoft Windows NT 3.51 server that supports Net BEUI, NWLink IPX/  
SPX, and NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, open the “NETWORK” folder, and double-click the  
“NETWORK SETUP” icon.  
6 Select “Networks” and choose “Install Microsoft Windows Network” and  
click on “OK.”  
7 Click on “Drivers” then on “Add Adapter.”  
8 With “Unlisted or Updated Network Adapter”, click on “OK.”  
9 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\” and hit enter. (If you have an HP preloaded HDD, set the path to  
D:\LANDRV\LNSTRM\DISK2\”)  
 
3 Connecting to a Windows NT 3.51 Server  
Windows for Workgroups  
10 Select “IBM Streamer Family Adapter” and click on “OK.”  
11 Verify that “IBM Streamer Family Family Adapter [NDIS2]” is listed under  
“Network Drivers” and clcik on “Close.”  
12 Click on “OK” in the “Network Setup” window.  
13 Specify your User Name, Workgroup Name, Computer Name, and click on  
“OK.”  
14 After files copy, click on “OK” to approve the modification of your  
CONFIG.SYS, AUTOEXEC.BAT, AND SYSTEM.INI files.  
15 Click on “Restart Computer” and the installation is complete.  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2.  
• IBM AUTO LANStreamer PCI card and drivers disk  
Driver Name: W95setup.inf Size: 40KB Date: 9/17/96  
• Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 When Windows 95 restarts a message will appear that new hardware has  
been found.  
6 Insert disk , 4 of 6, IBM Auto LANStreamer driver diskette.  
7 Click the “Next” button to begin hardware wizard.  
8 Click on “Other Locations” in the “Update Device Driver Location” dialog  
box, and set path to “A:\WIN95” then click “OK” (If you have an HP pre-  
loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK4\WIN95\”).  
9 “IBM Auto LANStreamer PCI Adapter(NDIS3)” should now be listed.  
Click on “Finish.”  
10 When prompted to insert the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click “OK.”  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
11 Insert Disk 1 of 6 of IBM Auto LANStreamer drivers disks and set path to  
“A:\” (If you have an HP pre-loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK1\”).  
12 Click “OK” to continue installation.  
13 Click “OK” to the “Network” dialog box, to provide computer / work group  
names.  
14 Specify your Computer Name, Workgroup, and Computer Description. (If  
you do not have the required information, contact your network  
administrator)  
15 Click on the “Configuration” folder in the “Network” dialog box.  
16 Click on “Add” and then “Protocol” from “Select Network Component  
Type” dialog box , then click on “Add”.  
17 Pick “Microsoft” from the “Manufacturers:” and “TCP/IP”, then click on  
“OK”.  
18 Highlight the “TCP/IP” network component and click on the “Properties”  
button.  
19 If you know your TCP/IP settings, enter them in the “TCP/IP Properties”  
dialog box, other wise leave the IP address choice checked “Obtain an IP  
address automatically”, and click “OK” . (If you do not have the required  
information, contact your network administrator)  
20 Click on the “Close” button, and click on “OK” for “IBM AUTO  
LANStreamer Properties” dialog box.  
21 When prompted for your Windows 95 files, click on “OK.”  
22 Set the path to your Windows 95 files and click “OK” to the “Insert Disk”  
dialog box. (If you have an HP pre-loaded HDD, set the path statement to  
“C:\MASTERS\WIN95\SYSTEM\CABS\”).  
23 When prompted for the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
24 Insert disk 4 of 6, set the path to “A:\WIN95” and click on “OK.” (If you  
have an HP pre-loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK4\WIN95\”)  
25 Click on “Yes” button to finish the setup installation and restart your  
computer.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
Windows NT  
Workstation  
Version 3.51  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 3.51 installed.  
• IBM AUTO LANStreamer PCI Drivers diskettes Ver. 3.04  
• DriverName:OEMSETUP.inf Size:67KB Date:10/18/96  
• Microsoft Windows NT Workstation 3.51 and Service Pack Media.  
• Microsoft Windows NT Server 3.51machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, open the “MAIN” program group , and double-click  
on “Control Panel” Icon.  
6 Select the “Network” icon in the “Control Panel” program group.  
7 Click on “YES” in the “Network Settings“ dialog box, and NT Networking  
will be installed on your computer.  
8 Insert the Windows NT Workstaion CD.  
9 In the “Windows NT Setup” enter the path to your NT files, and click on  
the “Continue” button. (If you have an HP preloaded HDD, set path to  
“C:\I386”)  
10 Click on the “Do Not Detect” button from the “Network Adapter Card  
Detection” dialog box, and click on “Continue” in the second “Network  
Adapter Card Detection” dialog box.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
11 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer”, then click “Continue“.  
12 Set the path to “A:\NT” in the “Insert Disk” dialog box, and then insert the  
disk 4 of 6 , Auto LANStreamer PCI drivers disk. (If you have an HP  
preloaded HDD, set path to “C:\LANDRV\LNSTRM\DISK4\NT\”)  
13 Click “OK” at the “Install Driver” dialog box.  
14 Select “IBM Streamer Family Adapters” in the “Select OEM Option” dialog  
box, and click “OK”.  
15 Click on the “OK” button in the “IBM Auto LANStreamer PCI Adapter”  
dialog box.  
16 Choose the default Protocol TCP/IP, and any additional Network  
Protocols by clicking the check boxes in the “Windows NT Setup” dialog  
box, and click “Continue.” (If you do not have the required information,  
contact your network administrator)  
17 Check the boxes to add additional TCP/IP components, and click on the  
“Continue” button.  
18 Click “OK” for the review of network settings, or “Network Settings”  
dialog box.  
19 Set your IP address information in the “TCP/IP Configuration” dialog box,  
and click “OK”. (If you do not have the required TCP/IP settings, contact  
your network administrator)  
20 At the “Domain/Workgroup Settings” dialog box, click on “OK” to accept  
the default “Workgroup” as your workgroup name. (If you do not have the  
required information, contact your network administrator)  
21 To complete the installation, remove the floppy disk, and click on “Restart  
Computer” in the “Windows NT Workstation Networking Setup” dialog  
box.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 4.0  
Windows NT  
Workstation  
Version 4.0  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 4.0 installed.  
• IBM AUTO LANStreamer PCI Drivers diskettes Ver. 3.04  
• DriverName:OEMSETUP.inf Size:67KB Date:10/18/96  
• Microsoft Windows NT Workstation 4.0 and Service Pack Media.  
• Microsoft Windows NT Server 3.51machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, log into NT workstation with administrator  
privileges. (If you do not have the required information, contact your  
network administrator)  
6 Click on “Start”, up to “Settings”, and open “Control Panel.”  
7 Select the “Network” icon in the “Control Panel” program group.  
8 Click on “YES” in the “Network Settings“ dialog box, and NT Networking  
will be installed on your computer.  
9 With “Wired to the Network” checked, click on “Next.”  
10 Click on “Select from List”, then click “Have Disk.”  
11 Set the path to “A:\NT” in the “Insert Disk” dialog box, and then insert the  
disk 4 of 6 , Auto LANStreamer PCI drivers disk. (If you have an HP  
preloaded HDD, set path to “C:\LANDRV\LNSTRM\DISK4\NT\”)  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 4.0  
12 Select “IBM Streamer Family Adapters” in the “Select OEM Option” dialog  
box, and click “OK”.  
13 With “IBM Streamer Family Adapters” listed, click on “Next.”  
14 Choose the default Protocol TCP/IP, and any additional Network  
Protocols by clicking the check boxes in the “Network Protocols” dialog  
box, and click “Next.” (If you do not have the required information,  
contact your network administrator)  
15 Click “OK” for the review of network services, and click on “Next.”  
16 Click on “Next” to install the selected components.  
17 Insert the Windows NT Workstaion CD.  
18 In the “Windows NT Setup” enter the path to your NT files, and click on  
the “Continue” button. (If you have an HP preloaded HDD, set path to  
“C:\I386”)  
19 Click on the “OK” button in the “IBM Auto LANStreamer PCI Adapter”  
dialog box.  
20 Click accordingly if you plan on using DHCP or if you plan on specifying  
your IP address manually.  
21 Specify your IP information or click on “Obtain an IP address from a DHCP  
server” and click “OK.”  
22 At the “Show Bindings for” window, click on “Next.”  
23 Click on “Next” to start the network.  
24 Specify your “Domain/Workgroup Settings”, and click on “Next.” (If you  
do not have the required information, contact your network  
administrator)  
25 Verify that “Networking has been installed on this computer” and click on  
“Finish.”  
26 To complete the installation, remove the floppy disk, and click on “Yes” to  
restart your computer.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 4.0  
4 Connecting to a Windows NT Server 4.0  
Windows NT  
Workstation  
Version 4.0  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 4.0 installed.  
• IBM AUTO LANStreamer PCI Drivers diskettes Ver. 3.04  
• DriverName:OEMSETUP.inf Size:67KB Date:10/18/96  
• Microsoft Windows NT Workstation 4.0 and Service Pack Media.  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, log into NT workstation with administrator  
privileges. (If you do not have the required information, contact your  
network administrator)  
6 Click on “Start”, up to “Settings”, and open “Control Panel.”  
7 Select the “Network” icon in the “Control Panel” program group.  
8 Click on “YES” in the “Network Settings“ dialog box, and NT Networking  
will be installed on your computer.  
9 With “Wired to the Network” checked, click on “Next.”  
10 Click on “Select from List”, then click “Have Disk.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 4.0  
11 Set the path to “A:\NT” in the “Insert Disk” dialog box, and then insert the  
disk 4 of 6 , Auto LANStreamer PCI drivers disk. (If you have an HP  
preloaded HDD, set path to “C:\LANDRV\LNSTRM\DISK4\NT\”)  
12 Select “IBM Streamer Family Adapters” in the “Select OEM Option” dialog  
box, and click “OK”.  
13 With “IBM Streamer Family Adapters” listed, click on “Next.”  
14 Choose the default Protocol TCP/IP, and any additional Network  
Protocols by clicking the check boxes in the “Network Protocols” dialog  
box, and click “Next.” (If you do not have the required information,  
contact your network administrator)  
15 Click “OK” for the review of network services, and click on “Next.”  
16 Click on “Next” to install the selected components.  
17 Insert the Windows NT Workstaion CD.  
18 In the “Windows NT Setup” enter the path to your NT files, and click on  
the “Continue” button. (If you have an HP preloaded HDD, set path to  
“C:\I386”)  
19 Click on the “OK” button in the “IBM Auto LANStreamer PCI Adapter”  
dialog box.  
20 Click accordingly if you plan on using DHCP or if you plan on specifying  
your IP address manually.  
21 Specify your IP information or click on “Obtain an IP address from a DHCP  
server” and click “OK.”  
22 At the “Show Bindings for” window, click on “Next.”  
23 Click on “Next” to start the network.  
24 Specify your “Domain/Workgroup Settings”, and click on “Next.” (If you  
do not have the required information, contact your network  
administrator)  
25 Verify that “Networking has been installed on this computer” and click on  
“Finish.”  
26 To complete the installation, remove the floppy disk, and click on “Yes” to  
restart your computer.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
Windows NT  
Workstation  
Version 3.51  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 3.51 installed.  
• IBM AUTO LANStreamer PCI Drivers diskettes Ver. 3.04  
• DriverName:OEMSETUP.inf Size:67KB Date:10/18/96  
• Microsoft Windows NT Workstation 3.51 and Service Pack Media.  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, open the “MAIN” program group , and double-click  
on “Control Panel” Icon.  
6 Select the “Network” icon in the “Control Panel” program group.  
7 Click on “YES” in the “Network Settings“ dialog box, and NT Networking  
will be installed on your computer.  
8 Insert the Windows NT Workstaion CD.  
9 In the “Windows NT Setup” enter the path to your NT files, and click on  
the “Continue” button. (If you have an HP preloaded HDD, set path to  
“C:\I386”)  
10 Click on the “Do Not Detect” button from the “Network Adapter Card  
Detection” dialog box, and click on “Continue” in the second “Network  
Adapter Card Detection” dialog box.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
11 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer”, then click “Continue“.  
12 Set the path to “A:\NT” in the “Insert Disk” dialog box, and then insert the  
disk 4 of 6 , Auto LANStreamer PCI drivers disk. (If you have an HP  
preloaded HDD, set path to “C:\LANDRV\LNSTRM\DISK4\NT\”)  
13 Click “OK” at the “Install Driver” dialog box.  
14 Select “IBM Streamer Family Adapters” in the “Select OEM Option” dialog  
box, and click “OK”.  
15 Click on the “OK” button in the “IBM Auto LANStreamer PCI Adapter”  
dialog box.  
16 Choose the default Protocol TCP/IP, and any additional Network  
Protocols by clicking the check boxes in the “Windows NT Setup” dialog  
box, and click “Continue.” (If you do not have the required information,  
contact your network administrator)  
17 Check the boxes to add additional TCP/IP components, and click on the  
“Continue” button.  
18 Click “OK” for the review of network settings, or “Network Settings”  
dialog box.  
19 Set your IP address information in the “TCP/IP Configuration” dialog box,  
and click “OK”.  
(If you do not have the required TCP/IP settings, contact your network  
administrator)  
20 At the “Domain/Workgroup Settings” dialog box, click on “OK” to accept  
the default “Workgroup” as your workgroup name. (If you do not have the  
required information, contact your network administrator)  
21 To complete the installation, remove the floppy disk, and click on “Restart  
Computer” in the “Windows NT Workstation Networking Setup” dialog  
box.  
 
4 Connecting to a Windows NT Server 4.0  
Windows for Workgroups  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.  
• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95  
• Microsoft Windows NT 4.0 server that supports Net BEUI, NWLink IPX/  
SPX, and NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
• Interrupt  
9 (2)  
• I/O Address  
FCC0-h  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 After windows loads, open the “NETWORK” folder, and double-click the  
“NETWORK SETUP” icon.  
6 Select “Networks” and choose “Install Microsoft Windows Network” and  
click on “OK.”  
7 Click on “Drivers” then on “Add Adapter.”  
8 With “Unlisted or Updated Network Adapter”, click on “OK.”  
9 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path  
to “A:\” and hit enter. (If you have an HP preloaded HDD, set the path to  
D:\LANDRV\LNSTRM\DISK2\”)  
10 Select “IBM Streamer Family Adapter” and click on “OK.”  
11 Verify that “IBM Streamer Family Family Adapter [NDIS2]” is listed under  
“Network Drivers” and clcik on “Close.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows for Workgroups  
12 Click on “OK” in the “Network Setup” window.  
13 Specify your User Name, Workgroup Name, Computer Name, and click on  
“OK.”  
14 After files copy, click on “OK” to approve the modification of your  
CONFIG.SYS, AUTOEXEC.BAT, AND SYSTEM.INI files.  
15 Click on “Restart Computer” and the installation is complete.  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2.  
• IBM AUTO LANStreamer PCI card and drivers disk  
Driver Name: W95setup.inf Size: 40KB Date: 9/17/96  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
FC00h  
9
• Interrupt Request Level  
Procedure  
1 With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR  
adapter card into a PCI slot.  
2 Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer  
PCI Diagnostic Disk) and power on the machine.  
3 After the machine boots, verify that the adapter finished testing and that  
the adapter is “OK.”  
4 Click on “F3” to exit, and then press “CTRL+ALT+DEL.”  
5 When Windows 95 restarts a message will appear that new hardware has  
been found.  
6 Insert disk , 4 of 6, IBM Auto LANStreamer driver diskette.  
7 Click the “Next” button to begin hardware wizard.  
8 Click on “Other Locations” in the “Update Device Driver Location” dialog  
box, and set path to “A:\WIN95” then click “OK” (If you have an HP pre-  
loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK4\WIN95\”).  
9 “IBM Auto LANStreamer PCI Adapter(NDIS3)” should now be listed.  
Click on “Finish.”  
10 When prompted to insert the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click “OK.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
11 Insert Disk 1 of 6 of IBM Auto LANStreamer drivers disks and set path to  
“A:\” (If you have an HP pre-loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK1\”).  
12 Click “OK” to continue installation.  
13 Click “OK” to the “Network” dialog box, to provide computer / work group  
names.  
14 Specify your Computer Name, Workgroup, and Computer Description. (If  
you do not have the required information, contact your network  
administrator)  
15 Click on the “Configuration” folder in the “Network” dialog box.  
16 Click on “Add” and then “Protocol” from “Select Network Component  
Type” dialog box , then click on “Add”.  
17 Pick “Microsoft” from the “Manufacturers:” and “TCP/IP”, then click on  
“OK”.  
18 Highlight the “TCP/IP” network component and click on the “Properties”  
button.  
19 If you know your TCP/IP settings, enter them in the “TCP/IP Properties”  
dialog box, other wise leave the IP address choice checked “Obtain an IP  
address automatically”, and click “OK” . (If you do not have the required  
information, contact your network administrator)  
20 Click on the “Close” button, and click on “OK” for “IBM AUTO  
LANStreamer Properties” dialog box.  
21 When prompted for your Windows 95 files, click on “OK.”  
22 Set the path to your Windows 95 files and click “OK” to the “Insert Disk”  
dialog box. (If you have an HP pre-loaded HDD, set the path statement to  
“C:\MASTERS\WIN95\SYSTEM\CABS\”).  
23 When prompted for the disk labeled “IBM Streamer Family Adapter  
Option Diskette”, click on “OK.”  
24 Insert disk 4 of 6, set the path to “A:\WIN95” and click on “OK.” (If you  
have an HP pre-loaded HDD, set the path statement to  
“C:\LANDRV\LNSTRM\DISK4\WIN95\”)  
25 Click on “Yes” button to finish the setup installation and restart your  
computer.  
 
 
Version Number Lans PCI Rev.1  
 

Graco Baby Accessories ISPS035AA User Manual
Grizzly Car Amplifier H6021 User Manual
Grizzly Kitchen Utensil G5938 User Manual
Grizzly Switch G4572 User Manual
Harman Kardon Stereo Receiver AVR 2000 User Manual
Havis Shields Drill F2 User Manual
Honeywell Door RCWL110A User Manual
Honeywell Fan HT 800 User Manual
HP Hewlett Packard TV DVD Combo C5445 90904 User Manual
Hunter Fan Fan 23802 User Manual