Electrolux EHG 691 User Manual

Gas hobs  
INSTRUCTION BOOKLET  
Please read this instruction booklet before using the appliance  
Mod. EHG 673 - EHG 691  
35675-8203  
GB  
Contents  
For the Installer  
For the User  
Instructions for the Installer  
Engineers technical data  
Important Safety Requirements  
Installation  
7
7
Important Safety Information  
Description of the Hobs  
Operation  
2
3
4
4
5
5
6
6
8
8
Maintenance and Cleaning  
Something Not Working?  
Service and Spare Parts  
Customer Care Department  
Guarantee Conditions  
Building In  
9
Electrical connections  
Wiring Diagram  
10  
11  
11  
13  
14  
Fault Finding  
Commissioning  
Conversion from Natural Gas to LPG  
Description of the Hobs  
3
EHG 673  
2
3
1
4
5
EHG 691  
3
6
3
2
1
1. Hob Top  
2. Rapid Burner  
3. Semi-rapid Burners  
4. Auxiliary Burner  
5
4
5. Control knobs  
6. Electric Ignition Push Button  
3
Operation  
Hob Burners  
To light a burner:  
To light a burner:  
F
F
Mod. EHG 673  
Mod. EHG 691  
l
l
l
pushtheelectricignitionpushbuttonwhichismarked  
by a little spark;  
l
push in the relevant control knob and turn it  
anticlockwise to maximum position.  
at the same time turn the relevant control knob  
anticlockwise to maximum position;  
then adjust the flame as required.  
l
Upon ignition, keep the knob pushed down for about  
5 seconds. This will allow the "thermocouple" (see  
diagram) to be heated and the safety device to be  
switched off, otherwise the gas supply would be  
interrupted.  
If the burner does not ignite, turn the control knob to  
zero, and try again.  
l
l
Then adjust the flame as required.  
If the burner does not ignite, turn the control knob to  
zero, and try again.  
To ensure maximum burner efficiency, you should only  
use pots and pans with a flat bottom fitting the size of  
the burner used (see table).  
Burner  
minimum  
diameter  
maximum  
diameter  
Large  
Medium  
Small  
(rapid)180  
(semi-rapid)120  
(auxiliary)80  
mm.  
260  
mm.  
160  
mm.  
mm.  
mm.  
mm.  
220  
If you use a saucepan which is smaller than the  
recommended size, the flame will spread beyond  
the bottom of the vessel, causing the handle to  
overheat.  
As soon as a liquid starts boiling, turn down the  
flame so that it will barely keep the liquid  
simmering.  
FO 0204  
A - Burner cap  
Take care when frying food in hot oil or fat, as  
the overheated splashes could easily ignite.  
B- Burner crown  
C- Ignition electrode  
D- Thermocouple  
If the control knobs become difficult to turn, please  
contact your local Electrolux Service Centre.  
Maintenance and Cleaning  
Should the hob top become heavily soiled, the following  
products are recommended:  
- For stainless steel hobs use a proprietary stainless  
steel cleaner.  
- For other hobs use Hob Brite or Bar Keepers Friend.  
Before any maintenance or cleaning can be carried  
out, you must DISCONNECT the hob from the  
electricity supply.  
The hob is best cleaned whilst it is still warm, as  
spillage can be removed more easily than if it is  
left to cool.  
Pan Supports  
The Hob Top  
Thepansupportsaredishwasherproof.Ifwashingthem  
by hand, take care when drying them as the enamelling  
process occasionally leaves rough edges. If necessay,  
remove stubborn stains using a paste cleaner.  
Regularly wipe over the hob top using a soft cloth well  
wrungoutinwarmwatertowhichalittlewashingupliquid  
has been added. Avoid the use of the following:  
-householddetergentandbleaches;  
-impregnatedpadsunsuitablefornon-sticksaucepans;  
- steel wool pads;  
- bath/sink stain removers.  
The Burners  
Theburnercapsandcrownscanberemovedforcleaning.  
Wash the burner caps and crowns using hot soapy  
water, and remove marks with a mild paste cleaner. A  
wellmoistenedsoapimpregnatedsteelwoolpadcanbe  
used with caution, if the marks are particularly difficult to  
remove.  
After cleaning, be sure to wipe dry with a soft cloth.  
4
Something Not Working?  
If the hob is not working correctly, please carry out the following checks before contacting your local Service Force  
Centre.  
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,  
a charge will be made even if the appliance is under guarantee.  
SYMPTOM  
SOLUTION  
n There is no spark when lighting the gas  
u Check that the unit is plugged in and the electrical  
supply is switched on  
u Check that the RCCB has not tripped (if fitted)  
u Check the mains fuse has not blown  
u Check the burner cap and crown have been  
replaced correctly, e.g. after cleaning.  
n The gas ring burns unevenly  
u Check the main jet is not blocked and the burner  
crown is clear of food particles.  
u Check the burner cap and crown have been  
replaced correctly, e.g. after cleaning.  
In-guarantee customers should ensure that the  
above checks have been made as the engineer will  
make a charge if the fault is not a mechanical or  
electrical breakdown.  
If after all these checks, your hob still does not operate  
correctly, contact your local Service Force Centre.  
Please note that it will be necessary to provide proof of  
purchase for any in-guarantee service calls.  
Service and Spare Parts  
In the event of your appliance requiring service, or if you  
wish to purchase spare parts, please contact your local  
Electrolux Service Force Centre by telephoning:  
0870 5 929929  
Your telephone call will be automatically routed to the  
Service Force Centre covering your post code area.  
For the address of your local Service Force Centre and  
further information about Service Force, please visit the  
Before calling out an engineer, please ensure you have  
read the details under the heading “Something Not  
Working.”  
When you contact the Service Force Centre you will need  
to give the following details:  
1. Your name, address and post code  
2. Your telephone number  
3. Clear and concise details of the fault  
4. The model and serial number of the appliance (found  
on the rating plate)  
5. The purchase date  
5
Customer Care Department  
For general enquiries concerning your Electrolux  
appliance or for further information on Electrolux products,  
please contact our Customer Care Department by letter  
or telephone at the address below or visit our website at  
www.electrolux.co.uk  
Customer Care Department  
ELECTROLUX  
55-77 High Street  
Slough  
Berkshire  
SL1 1DZ  
Tel. 08705 950950 (*)  
* calls to this number may be recorded for training purposes.  
Guarantee Conditions  
Electrolux Guarantee conditions  
*
Appliances found to be in use within a commercial  
or similar environment, plus those which are the  
subject to rental agreements.  
We, Electrolux, undertake that if, within 12 months of  
the date of the purchase, this Electrolux appliance or  
any part thereof is proved to be defective by any reason  
only of faulty workmanship or materials, we will, at our  
option, repair or replace the same FREE OF ANY  
CHARGE for labour, materials or carriage on condition  
that:  
*
Products of Electrolux manufacture which are not  
marketed by Electrolux.  
European Guarantee  
If you should move to another country within Europe then  
your guarantee moves with you to your new home  
subject to the following qualifications:  
*
*
*
The appliance has been correctly installed and used  
only on the gas and electricity supply stated on the  
rating plate.  
The appliance has been used for normal domestic  
purpose only, and in accordance with the  
manufacturer's instructions.  
*
The guarantee starts from the date you first  
purchased your product.  
*
The guarantee is for the same period and to the same  
extent for labour and parts as exist in the new country  
of use for this brand or range of products.  
The appliance has not been serviced, maintained,  
repaired, taken apart or tampered with by any person  
not authorised by us.  
*
*
*
This guarantee relates to you and cannot be  
transferred to another user.  
*
*
*
All service work under this guarantee must be  
undertaken by a Electrolux Service Centre.  
Your new home is within the European Community  
(EC) or European Free Trade Area.  
Any appliance or defective part replaced shall  
become the Company's property.  
The product is installed and used in accordance with  
our instructions and is only used domestically, i.e. a  
normal household  
This guarantee is in addition to your statutory and  
other legal rights.  
Home visits are made between 8.30am and 5.30pm  
Monday to Friday. Visits may be available outside these  
hours, in which case a premium will be charged.  
*
The product is installed taking into account  
regulations in your new country.  
Before you move, please contact your nearest Customer  
Care centre, listed below, to give them details of your  
new home. They will then ensure that the local Service  
Organisation is aware of your move and able to look after  
you and your appliances.  
Exclusions  
This guarantee does not cover:  
*
Damage or calls resulting from transportation,  
improper use or neglect, the replacement of any light  
bulbs or removable parts of glass or plastic.  
France  
Germany  
Italy  
Senlis  
+33 (0) 3 44 62 20 13  
+49 (0) 800 234 7378  
Nürnberg  
*
Costs incurred for calls to put right an appliance  
which is improperly installed or calls to appliance  
outside the United Kingdom.  
Pordenone +39 (0) 800 117511  
Stockholm +46 (0) 20 78 77 50  
Sweden  
UK  
Slough  
+44 (0)1753 219898  
6
Instructions for the Installer  
Engineers technical data  
Overall dimensions  
Ignition HT Spark  
Spark Generator  
Ispra Control's BF 50066 -  
220-240V 0.6 VA T 120  
Fixed  
Width:  
Depth:  
580 mm.  
500 mm.  
Spark Gap  
Rear Left Burner (semi-rapid)  
Heat Input  
2.0 kW (6824 BTU/HR)  
Cut out dimensions  
Width:  
Depth:  
550 mm.  
470 mm.  
Front Left Burner (rapid)  
Heat Input  
3.0 kW (10236 BTU/HR)  
2.8 kW L.P.G. (9554 BTU/HR)  
Rear Right Burner (semi-rapid)  
Supply connections  
Heat Input  
2.0 kW (6824 BTU/HR)  
Gas:  
Front Right Burner (auxiliary)  
R 1/2 inch (1/2 inch male) Rear right hand corner  
Heat Input  
1.0 kW (3413 BTU/HR)  
Electric:  
230-240V 50Hz supply, 3 core flexible cable with non  
rewireable plug fitted with a 3 amp cartridge fuse.  
BURNER  
RAPID  
(large)  
SEMI-RAPID  
(medium)  
AUXILIARY  
(small)  
TYPEOF  
GAS  
Characteristics  
POSITION  
MAX  
MIN  
MAX  
MIN  
MAX  
MIN  
NOMINALTHERMAL  
POWER(kW)  
3.0  
0.286  
119  
0.65  
0.062  
Adjust.  
2.0  
0.190  
96  
0.45  
1.0  
0.095  
70  
0.33  
NATURAL  
GAS  
20 mbar  
NOMINALFLOW  
RATE (m3/h)  
0.043  
0.031  
NOZZLEREFERENCE  
(1/100 mm)  
Adjust.  
Adjust.  
NOMINALTHERMAL  
POWER (kW)  
2.8  
202  
86  
0.65  
47  
2.0  
144  
71  
0.45  
32  
1.0  
72  
50  
0.33  
24  
LPG GAS  
28-30/37  
mbar  
NOMINALFLOW  
RATE (g/h)  
NOZZLEREFERENCE  
(1/100 mm)  
40  
32  
28  
APPLIANCE CLASS:  
3
Burner  
Dia. Tap By-pass  
1/100 mm  
APPLIANCE CATEGORY: II2H3+  
Auxiliary  
Semi-rapid  
Rapid  
28  
32  
40  
APPLIANCE GAS SUPPLY: Natural gas G20 / 20mbar  
Aerationadjustmentnone  
7
Important safety requirements  
FITTING THE GAS HOB  
WITHOUTACOOKERHOODABOVE  
This hob must be installed in accordance with the Gas  
Safety (Installation and Use) Regulations (Current Edition)  
and the IEE Wiring Regulations (Current Edition).  
Detailed recommendations are contained in the following  
British Standards Codes Of Practice: B.S. 6172/ B.S.  
5440, Part 2 and B.S. 6891 Current Editions.  
700 mm  
The hob should not be installed in a bed sitting room  
with a volume of less than 20 m3. If it is installed in a  
room of volume less than 5 m3 an air vent of effective  
area of 110 cm2 is required. If it is installed in a room of  
volume between 5 m3 and 10 m3 an air vent of effective  
area of 50 cm2 is required, while if the volume exceeds  
11 m3 no air vent is required.  
400 mm  
55 mm  
400 mm  
100 mm  
50 mm  
However, if the room has a door which opens directly to  
the outside no air vent is required even if the volume is  
between 5 m3 and 11 m3.  
If there are other fuel burning appliances in the same  
room, B.S. 5440 Part 2 Current Edition, should be  
consulted to determine the requisite air vent requirements.  
FO 0812  
FITTING THE GAS HOB  
WITHACOOKERHOODABOVE  
600 mm  
Location  
The hob may be located in a kitchen, a kitchen/diner or  
bed sitting room, but not in a bathroom, shower room or  
garage.  
650 mm  
Before making the cut out in the worktop ensure that the  
edges of the hob that are to be near either a side or rear  
wall have a minimum distance of 55 mm. between the  
edge of the hob and the wall.  
The minimum distance combustible material can be fitted  
above the hob is 400 mm. If it is fitted below 400 mm. a  
space of 50 mm. must be allowed from the edges of the  
hob.  
400 mm  
55 mm  
50 mm  
400 mm  
100 mm  
50 mm  
The minimum distance combustible material can be fitted  
directly above the hob is 700 mm.  
A minimum distance of 100 mm. must be left between  
the side edges of the hob and any adjacent cabinets or  
walls.  
FO 0813  
Installation  
IMPORTANT  
WHEN THE HOB IS FIRST INSTALLED  
Thishobmustbeinstalledbyqualifiedpersonnel  
to the relevant British Standards.  
Once the hob has been installed, it is important to  
remove any protective materials, which were put  
on in the factory.  
Any gas installation must be carried out by a  
registered CORGI installer.  
On the end of the shaft, which includes the G 1/2"  
threaded elbow, adjustment is fixed so that the washer  
is fitted between the components as shown in the  
diagram. Screw the parts together without using excessive  
force.  
The manufacturer will not accept liability, should  
the above instructions or any of the other safety  
instructions incorporated in this book be ignored.  
8
Gas Connection  
Connection to the gas supply should be with either rigid  
or semi-rigid pipe, i.e. steel or copper.  
The connection should be suitable for connecting to R  
1/2 (1/2 BSP male thread).  
When the final connection has been made, it is essential  
that a thorough leak test is carried out on the hob and  
installation.  
Ensure that the main connection pipe does not exert  
any strain on the hob.  
A) End of shaft with nut  
B) Washer  
C) Elbow  
FO 0264  
It is important to install the elbow correctly, with  
the shoulder on the end of the thread, fitted to the  
hob connecting pipe.  
Rectangular cut-out size for hob  
Failure to ensure the correct assembly will cause  
leakage of gas.  
Cut Out Size  
The dimensions of the cut-out are given in the diagram.  
470  
550  
Dimensions are given in mm.  
FO 2098  
1
ON/OFF SWITCH  
Building In  
Building over a cupboard or  
drawer  
FLEX  
OUTLET  
If the hob is to be installed above a cupboard or drawer  
it will be necessary to fit a heat resistant board below  
the base of the hob on the underside of the work  
surface.  
It is also recommended to carry out the electrical  
connection to the hob as shown in diagrams 1 and 2.  
FO 0763  
Building over a kitchen unit  
with door  
ON/OFF SWITCH  
3
2
Proper arrangements must be taken in designing the  
furniture unit, in order to avoid any contact with the  
bottom of the hob which can be heated when it is  
operated. The recommended solution is shown in  
diagram 3.  
The panel fitted under the hob ("a") should be easily  
removable to allow easy access if technical  
assistance is needed. The space behind the kitchen  
unit ("b") can be used for connections.  
a
60  
b
FLEX  
OUTLET  
FO 1013  
FO 0764  
Dimensions are given in mm.  
9
Fitting the Hob into the worktop  
Carry out the building in of the hob as follows:  
put the seals supplied with the hob, on the  
edges of the cut out taking care that the seals  
meet without overlapping;  
place the hob in the cut out, taking care that it  
is centred;  
fix the hob with the relevant fixing clamps and  
screws, as shown in the diagram. When the  
screws have been tightened, the excess seal  
can be removed.  
F
a
FO 0199  
The edge of the hob forms a double seal which prevents  
the ingress of liquids.  
a) Sealing gasket  
Electrical connections  
A cut off plug inserted into a 13 amp socket is  
a serious safety (shock) hazard. Ensure that  
the cut off plug is disposed of safely.  
Any electrical work required to install this hob  
should be carried out by a qualified electrician or  
competent person, in accordance with the current  
regulations.  
Permanent Connection  
THIS HOB MUST BE EARTHED.  
In the case of a permanent connection, it is necessary  
that you install a double pole switch between the hob  
and the electricity supply (mains), with a minimum gap  
of 3 mm. between the switch contacts and of a type  
suitable for the required load in compliance with the current  
electric regulations.  
The manufacturer declines any liability should these  
safety measures not be observed.  
This hob is designed to be connected to a 230-240V  
50Hz AC electrical supply.  
Before switching on, make sure the electricity supply  
voltage is the same as that indicated on the hob rating  
plate. The rating plate is located on the bottom of the  
hob. A copy is attached on the back cover of this book.  
The switch must not break the yellow and green earth  
cable at any point.  
Ensure that the hob supply cord does not come  
into contact with surfaces with temperatures  
higher than 50 deg. C.  
The hob is supplied with a 3 core flexible supply cord  
incorporating a 3amp plug fitted. In the event of having to  
change the fuse, a 3ampASTAapproved (BS 1362) fuse  
must be used.  
Supply cable replacement  
The cable used to connect the hob to the electrical supply  
must comply to the specifications given below.  
Should the plug need to be replaced for any reason, the  
wires in the mains lead are coloured in accordance with  
the following code:  
Green and Yellow - Earth  
Min. size Cable/flex Cable / flex type Fuse  
Blue  
- Neutral  
-Live  
0.75 mm2  
H05 V2V2-F (T90)  
3 A  
Brown  
— Connect the green and yellow (earth) wire to  
the terminal in the plug which is marked with  
F
the letter 'E' or the earth symbol  
green and yellow.  
or coloured  
— Connect the blue (neutral) wire to the terminal  
in the plug which is marked with the letter 'N' or  
coloured black.  
— Connect the brown (live) wire to the terminal in  
the plug which is marked with the letter 'L' or  
coloured red.  
Upon completion there must be no cut, or stray strands  
of wire present and the cord clamp must be secure over  
the outer sheath.  
FO 0390  
10  
Wiring Diagram  
L
1
A
2
3
4
5
6
0
220/240  
A. IGNITOR SWITCH  
B. IGNITOR UNIT  
B
N
Fault Finding  
SOCKET  
(face view)  
PLUG (with cover  
removed)  
Preliminary Electrical Systems  
Check  
( )  
Earth Wire  
Green/Yellow  
( )  
E
Blue  
Brown  
Green  
Yellow  
START  
Isolate appliance  
and carry out:  
A: Earth Continuity  
check.  
Neutral Wire  
Blue  
N
L
Blue  
Green  
Yellow  
Brown  
Carry out:  
D: Resistance to  
Earth check.  
Electricity supply  
should now be  
satisfactory.  
NO  
YES  
Carry out:  
C: Polarity check.  
Has inlet fuse blown?  
A. EARTH CONTINUITY CHECK -Appliance must be  
electrically disconnected - meter set on W (Ohms) x  
1 scale and adjust zero if necessary.  
NO  
YES  
a) Testleadsfromanyapplianceearthpointtoearth  
pin on plug. Resistance should be less than 0.1  
W (Ohm), check all earth wires for continuity and  
all contacts are clean and tight.  
Inlet wiring  
faulty.  
B. INSULATION CHECK - Appliance electrically  
Rectify any  
fault.  
disconnected, all switches ON.  
a) meter set on W (Ohms) x 1 scale.  
TestleadsfromLtoNinapplianceterminalblock.  
If meter reads «0» then there is a short circuit.  
b) meter set on W (Ohm) x 100 scale.  
Repeat test with leads from L to E. If meter reads  
less than ¥ (infinity) there is a fault.  
Isolate appliance and  
carry out:  
B: Insulation check.  
Rectify any fault  
including replacing  
fuses as necessary.  
NOTE - Should it be found that the fuse has failed  
but no fault is indicated - a detailed continuity check  
(i.e. by disconnecting and checking each  
component) is required to trace the faulty component.  
It is possible that a fault could occur as a result of  
local burning/arcing but no fault could be found under  
test. However a detailed visual inspection should  
reveal evidence of burning around the fault.  
11  
Ignition System / Gas Ignition  
YES  
Check gas supply at  
burner  
Ignitor does not spark  
NO  
Check plug top fuse  
and replace if  
necessary  
Light burner manually  
Check polarity and  
earth continuity of  
supply point  
Check by pass simmer  
adjusted  
Check position of the  
electrode  
Check earth continuity  
of appliance  
Check continuity from the tip of  
each electrode to the  
terminals 1 to 4 on the ignitor  
unit  
Check fitting of burners  
Check continuity from 'N' on the  
mains connector block and "O" on  
the ignitor unit  
Check continuity from 'L' on the  
mains connector block and the  
taps ignition switches  
Check for breaks in the  
insulation  
of the HT leads  
Check continuity from ignition  
switches connector to ignitor unit  
Change the taps  
ignition switches  
Change the ignitor unit  
12  
Commissioning  
When the hob has been fully installed it will be necessary  
to check the minimum flame setting. To do this, follow  
the procedure below.  
-
-
Turn the gas tap to the MAX position and ignite.  
Set the gas tap to the MIN flame position then turn  
the control knob from MIN to MAX several times. If  
the flame is unstable or is extinguished follow the  
procedure below.  
Procedure:  
Re-ignite the burner and set to MIN.  
Minimum adjustment screw  
FRemove the control knob.  
To adjust, use a thin bladed screwdriver and turn  
the adjustment screw (see diagram) until the flame  
is steady and does not extinguish, when the knob  
is turned from MIN to MAX. Repeat this procedure  
for all burners.  
Pressure Testing  
Remove left hand pan support and front left burner  
Fcap and crown.  
Fit manometer tube over the injector.  
Turn on the burner gas supply and ignite another  
burner.  
The pressure reading should be nominally 20mbar  
and must be between 17 mbar and 25mbar.  
Turn off the burner supplies.  
13  
Conversion from Natural Gas to LPG  
It is important to note that this model is designed for  
To adjust the gas rate  
use with natural gas but can be converted for use with  
With the aid of a thin bladed screwdriver completely  
butane or propane gas providing the correct injectors  
tighten down the by pass adjustment screw. Upon  
are fitted. The gas rate is adjusted to suit.  
completion affix the replacement rating plate on the under  
side of the hob.  
Method  
IMPORTANT  
Ensure that the gas taps are in the 'OFF' position  
Isolate the hob from the electrical supply  
Remove all pan supports, burner caps, rings, crowns  
and control knobs.  
The replacement/conversion of the gas hob should only  
be undertaken by a competent person.  
With the aid of a 7mm box spanner the burner injectors  
can then be unscrewed and replaced by the  
appropriate LPG injectors.  
14  
CUSTOMER CARE  
Electrolux  
55-77 High Street  
Slough  
Berkshire, SL1 1DZ  
Tel: 08705-950950  
© Electrolux plc 2003  
The Electrolux Group. The world’s No.1 choice.  
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than  
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and  
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.  

HP Hewlett Packard HP LP2065 20 User Manual
HP Hewlett Packard 1035I User Manual
Garland UCO E 05 User Manual
Gaggenau KG 291 CA User Manual
Dell POWEREDGE M915 User Manual
Dell Axim User Manual
Dacor EPICURE EG366 User Manual
BT Diverse 5200 User Manual
Asus Desktop Motherboard P8Z77 V LE PLUS User Manual
AOC Computer Monitor E941VA User Manual