Sub Zero Refrigerator 601RG User Manual

Planning Information  
Built-In Model 601RG  
All Refrigerator with Glass Door  
Lighted electronic  
control panel  
Serial and model  
number plate  
Triple-pane  
601RG  
UV resistant low-  
energy glass door  
Adjustable spill-proof  
glass shelves  
Model 601RG/F  
Framed  
Egg container  
Four-sided  
magnetic gaskets  
High humidity  
Door closers  
compartment  
Model 601RG/O  
Overlay  
Hermetically sealed  
refrigeration units  
Front venting allows unit  
to be completely built in  
Removable kickplate  
(Stainless steel design shown)  
Model 601RG/S (P/B)  
Stainless Steel  
With the installation of a harness kit, these  
appliances are Star-K compliant to meet strict  
religious regulations in conjunction with specific  
instructions found on star-k.org. You may purchase  
this harness kit through your Sub-Zero dealer.  
To obtain local dealer information, visit the Locator  
section of our website, subzero.com.  
The Sub-Zero Model 601RG all  
This handsome addition to Sub-Zero’s inventory of  
models offers you the ability to complement the  
commercial looking kitchen with ease. There are, obvi-  
ously, no door shelves, but there is no loss of storage  
space in this unit. A roll-out utility drawer is available  
as an option. Even with the glass door on this unit, you  
can assure your clients that this model still meets  
Department of Energy numbers.  
refrigerator with glass door is available in  
your choice of the framed, overlay or stain-  
less steel design application. Three stainless  
steel finishes are offered—classic (/S),  
platinum (/P) and carbon (/B).  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
1
11/06  
 
Planning Information  
Built-In Model 601RG  
S P E C I F I C A T I O N S  
Model 601RG  
All Refrigerator  
with Glass Door  
Overall Width  
36" (914)  
73" (1854)  
Overall Height  
M O D E L O P T I O N S  
Overall Depth  
24" (610)  
Framed Design  
601RG/F  
Refrigerator Capacity  
Minimum Height (levelers in)  
Door Swing Clearance  
20.1 cu ft (569 L)  
723/4" (1848)  
361/16" (916)  
Overlay Design  
601RG/O  
601RG/S  
601RG/P  
601RG/B  
Classic Stainless Steel  
Platinum Stainless Steel  
Carbon Stainless Steel  
Electrical Requirements  
Annual Energy Usage  
115 V AC, 60 Hz, 15 amp circuit  
400 kWh / $37  
(based on 9.06 cents per kilowatt hour)  
Energy Star Qualified  
You must allow 90 days from order to  
delivery for platinum and carbon finishes.  
Shipping Weight  
Special Note  
Framed – 400 lbs (181 kg)  
Overlay – 400 lbs (181 kg)  
Stainless Steel – 430 lbs (195 kg)  
A C C E S S O R I E S  
Side panels in white, almond and  
classic stainless steel  
Model 601RG has a triple-pane  
UV-resistant low-energy glass door  
Extended framed handle  
Specifications are subject to change without notice.  
Stainless steel and polished  
chrome handles for overlay design  
Roll-out deli basket  
Dozen egg container with lid  
90˚ and 105˚ door stop kits  
Accessories are available through your  
Sub-Zero dealer. To obtain local dealer  
information, visit the Locator section of  
our website, subzero.com.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
3
 
Planning Information  
Built-In Model 601RG  
I N S TA L L A T I O N S P E C I F I C A T I O N S  
24"  
(610)  
ROUGH  
OPENING  
DEPTH  
TOP VIEW  
1
35 /2"  
(902)  
ROUGH OPENING WIDTH  
3
72 /4"  
(1848)  
ROUGH  
OPENING  
HEIGHT  
LOCATE ELECTRICAL  
WITHIN SHADED AREA  
24"  
6"  
(610)  
(152)  
E
11"  
(279)  
FRONT VIEW  
D I M E N S I O N S  
Finished Rough Opening Width  
Finished Rough Opening Height  
Finished Rough Opening Depth  
Location of Electrical  
351/2" (902)  
723/4" (1848)  
24" (610)  
Within shaded area  
See Installation Instructions shipped with unit for detailed specifications.  
Refer to the Sub-Zero Design Guide pdf file for additional specifications.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
4
 
Planning Information  
Built-In Model 601RG  
I N S TA L L A T I O N N O T E S  
Refer to the illustrations and specifications  
for overall dimensions, finished rough opening  
dimensions and installation specifics.  
The refrigerator door panel must include a  
cut-out to accommodate the window. Refer to  
the panel specifications for exact dimensions.  
The glass portion of the door must be exposed  
and not covered by any part of the panel.  
Allow the door to open a minimum of 90˚ or  
you'll have problems removing drawers. With  
the door opening at 90˚, you may have to move  
drawers slightly to clear the door interior. Refer  
to the minimum door swing clearance in the  
specifications chart.  
A 115 volt, 60 Hz, 15 amp electrical supply  
is required. The supply circuit for this appliance  
must be protected by a 15 amp fuse or circuit  
breaker. It is recommended that a separate  
circuit, serving only this appliance, be provided.  
For corner installations, allow for a minimum  
3" (76) filler so that the door can open to 90˚.  
If you're using raised panels, consider using a  
wider filler. A 90˚ door stop is available as an  
accessory.  
All Built-In models are equipped with a 6'  
(1.8 m) power supply cord with a 3-prong  
grounding plug which must be plugged into a  
mating 3-prong grounding type wall receptacle.  
Locate electrical within the shaded area shown  
in the installation illustration.  
When units are installed side by side, a filler  
strip is recommended. The width of this filler  
strip will vary depending on the configuration  
and panels you use. An anchoring kit may also  
be used to attach two units together. This kit is  
available through your Sub-Zero dealer.  
You must follow all National Electrical Code  
regulations. In addition, be aware of local codes  
and ordinances when installing your service.  
To prevent the unit from tipping forward and  
provide a stable installation, the unit must be  
secured in place with an anti-tip blocking kit. If  
there is a solid soffit above the unit with clear-  
ance between the unit and the soffit of 1" (25)  
or less, you won't need to block the unit.  
Be sure to add the filler strip width to your  
finished rough opening dimension. In any side-  
by-side installation without a filler strip, add an  
additional 1/2" (13) to your combined numbers.  
This will allow for the proper width.  
Refer to the full-scale illustrations at the end  
of this section for specifics on door openings  
and filler size alternatives.  
For installations with clearances of more  
than 1" (25), you must block the unit with the  
anti-tip blocking kit (wood block and hardware)  
provided with each Built-In unit.  
If your client has chosen the stainless steel  
design, the unit will be shipped complete with  
wrapped stainless steel doors and handle  
hardware. You will not have to install front  
panels.  
Refer to the Built-In Installation Instructions  
packed with the appliance, which provides  
step-by-step procedures for making sure the  
unit is installed properly.  
If your client has chosen the framed or  
overlay design, you will be adding front panels  
to give the unit the custom Sub-Zero look. The  
overlay design also allows you to add your own  
handles, or you may choose accessory handles  
available through your Sub-Zero dealer. Refer to  
pages 6–10 for detailed information on adding  
panels.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
5
 
Planning Information  
Built-In Model 601RG  
A D D I N G PA N E L S  
In your plan for panels, be sure you are working with the  
Sub-Zero panel design family called for in your design. If  
you have chosen the stainless steel design, the unit will be  
shipped complete with wrapped stainless steel doors and  
handle hardware. You will not have to install front door  
panels.  
If you and your client have ordered a framed or overlay  
design model, you will be adding panels to give the unit  
the custom Sub-Zero look. Specifications on the following  
pages provide installation considerations for framed and  
overlay door panels.  
Side panels can be used with the framed, overlay and  
stainless steel design applications. Refer to specifications  
on page 10.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
6
 
Planning Information  
Built-In Model 601RG  
F R A M E D PA N E L S  
If the thickness of the custom panels is less than 1/4"  
(6), they must be backed up with a sheet of shim material  
to build the total thickness to 1/4" (6). If the panel is thicker  
than 1/4" (6), an edge must be routed around the panel to  
ensure a proper fit. Refer to the illustrations on this page.  
F R A M E D PA N E L S  
IMPORTANT NOTE: Routing, recessing or optional  
extended handles may be required on raised panels for  
finger clearance under the handle. Refer to the full-scale  
illustrations on pages 1114.  
1
PANELS /4" (6) THICK OR LESS  
Trim reveal  
1
/4" (6) min  
IMPORTANT NOTE: The weight of each panel cannot  
exceed 50 lbs (23 kg).  
The traditional framed models come with an 11" (279)  
louvered grille and elegant full-length handle. Optional  
extended full-length handles that provide additional finger  
clearance for raised panels are available through your  
Sub-Zero dealer. To obtain local dealer information, visit  
the Locator section of our website, subzero.com.  
1
/4" (6) Panel  
Framed door panel 1/4" (6) thick or less  
To install framed panels, refer to the installation instruc-  
tions shipped with each unit. These instructions can also  
be found on our website, subzero.com.  
1
PANELS THICKER THAN /4" (6)  
Trim reveal  
/4" (6) min  
1
The refrigerator door panel must include a cut-out to  
accommodate the window. Refer to the chart below for  
exact dimensions. The glass portion of the door must be  
exposed and not covered by any part of the panel.  
1
Rout to /4" (6)  
thickness  
F R A M E D PA N E L D I M E N S I O N S  
Framed door panel thicker than 1/4" (6)  
WIDTH  
HEIGHT  
Door Panel  
341/8" (867) 5815/16"(1497)  
A – 2915/32" (749)  
Handle Recess Location  
Window Cut-Out  
B
253/8" (645)  
413/16" (1046)  
B – 43/8" (111)  
50 lbs (23 kg)  
B
B
Window Cut-Out Location  
Maximum Panel Weight  
14" (356)  
H
A
3
13 /8" (340)  
W
Framed Door Panel  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
7
 
Planning Information  
Built-In Model 601RG  
O V E R L AY PA N E L S  
The overlay design allows decorative panels to cover the  
door trim for a more seamless appearance that blends  
with the design of the room. To achieve this look, the  
most common way is to work with three panels—the  
decorative overlay panel, a .10" (3) spacer panel and a 1/4"  
(6) backer panel. Depending on your cabinet manufacturer,  
this could be one panel routed for different dimensions or  
more likely, three different panels.  
O V E R L AY PA N E L S  
Spacer Panel  
.10"  
Regardless of the physical construction of the panels  
(routing or three panel assembly), you will need to follow  
the exact dimensions and panel placement to ensure a  
proper fit.  
(3)  
Overlay Panel  
The top illustration on this page is a cross section view of  
the three panel assembly showing placement of the  
door/drawer/grille trim. The bottom illustration shows a  
rear view of the three panel assembly and critical dimen-  
sions, standard for all overlay models.  
1
/4" (6) Backer Panel  
5
/16" (8) min  
5
/32" (4)  
/16" (2)  
Door/Drawer/  
Grille Trim  
1
Overlay models will come with no handle hardware,  
because the beauty of this design is that you can match  
the surrounding cabinetry hardware. For overlay door panel  
dimensions, refer to specifications on page 9.  
Three panel assembly—cross section  
IMPORTANT NOTE: Keep in mind that the Sub-Zero door  
panels have the potential for hitting adjacent cabinets  
and/or countertops when they are opened. You need to be  
aware of your surrounding cabinetry and space limitations  
when using the overlay models. Refer to the full-scale  
illustrations on pages 1314.  
Overlay Panel  
Spacer Panel  
IMPORTANT NOTE: The weight of each door panel  
assembly cannot exceed 50 lbs (23 kg). The total thick-  
ness of all panels for an overlay model must be at least  
5/8" (16) thick.  
Backer  
3
~ /4"  
Panel  
(19)  
1
.10" (3) /4" (6)  
To install overlay panels, refer to the installation instruc-  
tions shipped with each unit. These instructions can also  
be found on our website, subzero.com.  
Three panel assembly—rear view  
Do not exceed the dimensions listed for the overlay  
grille panel. The decorative panel cannot be any larger  
or it may restrict the air flow to the compressor area  
and cause problems with the operation of the unit.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
8
 
Planning Information  
Built-In Model 601RG  
O V E R L AY PA N E L S  
The refrigerator door panel must include a cut-out to  
accommodate the window. Refer to the chart below for  
exact dimensions. The glass portion of the door must be  
exposed and not covered by any part of the panel.  
A
O V E R L AY PA N E L D I M E N S I O N S  
A
A
WIDTH  
347/16" (875)  
331/2" (851)  
HEIGHT  
Door Panel  
591/4" (1505)  
585/16" (1481)  
H
Door Spacer  
Door Backer  
341/8" (867) 5815/16"(1497)  
Window Cut-Out  
Window Cut-Out Location  
257/16" (646)  
411/4" (1048)  
A – 41/2" (114)  
50 lbs (23 kg)  
1
13 /2" (343)  
W
Maximum Weight (panel assembly)  
Overlay Door Panel  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
9
 
Planning Information  
Built-In Model 601RG  
S I D E PA N E L S  
Side panels can be used with the framed, overlay and  
stainless steel design applications. When planning for side  
panels with the installation of the Built-In model, you need  
to be aware of space configuration to achieve a pleasing  
fit. Depending on the exact panel you are using with your  
unit, the height of the panel will vary.  
S I D E PA N E L S  
Cut-outs around the toe kick and grille area are required if  
a 1/4" (6) thick panel will be inserted into the main frame  
channel. The panel will need to be 24" (610) deep. Refer to  
the illustration on this page for placement of toe kick and  
grille area cut-outs. If a 3/8" (10) thick panel is used, the  
panel will abut the main frame and should be 237/8" (606)  
deep. The toe kick area may or may not be cut out  
depending on the look you want to achieve.  
237/8" (606)  
BEHIND FRAME  
IMPORTANT NOTE: The use of side panels may change  
the width of your rough opening.  
H A R D W A R E C O N S I D E R AT I O N S  
Overlay models come without handle hardware. The  
beauty of this design is that you can match the surround-  
ing cabinet hardware. You or the cabinet manufacturer  
must provide handle hardware to match the overall deco-  
rating scheme.  
4" (102)  
3" (76)  
Cut-outs for grille and toe kick area  
The handle hardware must be installed before installing  
the panel assembly. Use larger D-style handles. If screws  
with thick heads are used, the screws will need to be  
countersunk into the door before the panel is put into  
place. Refer to the full-scale illustrations on pages 11–12  
for handle hardware considerations.  
IMPORTANT NOTE: Sub-Zero does not recommend using  
single pull knobs on any of its Built-In models.  
Optional stainless steel handles are available in a variety of  
diameters and lengths in the classic, platinum and carbon  
stainless steel finishes and polished chrome. Contact  
your Sub-Zero dealer for specifics. To obtain local dealer  
information, visit the Locator section of our website,  
subzero.com.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
10  
 
Planning Information  
Built-In Model 601RG  
H A N D L E P R O F I L E  
F R A M E D A P P L I C AT I O N  
OPTIONAL  
EXTENDED  
FULL-LENGTH  
HANDLE  
1"  
2"  
3"  
(25)  
(51)  
(76)  
1
1 /4"(32) PANEL  
STANDARD  
FULL-LENGTH  
HANDLE  
1"(25) PANEL  
3
/4"(19) PANEL  
1
/2"(13) PANEL  
1
/4"(6) PANEL  
1
/4"(6) FRAMED PANEL  
DOOR  
F U L L - S C A L E T E M P L A T E S  
H A N D L E P R O F I L E  
The following full-scale illustrations enable you  
to understand some of the unique situations  
you may face as you design the Built-In units  
into homes. These templates can be easily  
photocopied or used in your tracings.  
The full-scale illustration above shows handle  
placement for the framed application standard  
full-length handle and the optional extended  
full-length handle shown in the dashed line.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
11  
 
Planning Information  
Built-In Model 601RG  
H A N D L E P R O F I L E  
S TA I N L E S S S T E E L  
/
O V E R L AY A P P L I C AT I O N S  
STANDARD STAINLESS STEEL HANDLE  
2"  
3"  
(51)  
(76)  
1
1 /4" (32) PANEL  
1" (25) PANEL  
3
/4" (19) PANEL  
5
1
/8" (16) PANEL  
/2" (13) PANEL  
1
/4" (6) PANEL  
DOOR  
NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE  
MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.  
PA N E L A N D H A N D L E P R O F I L E  
The full-scale illustration above shows handle  
placement for the standard stainless steel  
handle on the wrapped stainless steel door and  
on overlay panel applications shown in the  
dashed line.  
IMPORTANT NOTE: For overlay applications,  
the optional stainless steel handle must be  
mounted on a panel at least 5/8" (16) thick.  
For overlay applications, mount door handles  
close to the opening edge of the door for ease  
of opening.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
12  
 
Planning Information  
Built-In Model 601RG  
PA N E L A N D H A N D L E P R O F I L E  
1 3 0 ˚ D O O R O P E N I N G  
130˚ DOOR OPENING  
WITH 2" (51) FILLER STRIP  
(TOP VIEW)  
SUB-ZERO UNIT  
FILLER STRIP  
2" (51)  
ALLOW FOR FILLER LAP  
BEHIND FLANGE  
DOOR CLOSED  
OVERLAY PANEL  
3/4" (19) THICK  
(NOMINAL)  
MAIN FRAME  
HINGE  
APPROX  
PROFILE OF  
STAINLESS  
STEEL DOOR  
AND HANDLE  
STANDARD  
FRAMED  
FULL-LENGTH  
HANDLE  
DOOR OPEN @ 130˚  
OPTIONAL  
FRAMED EXTENDED  
FULL-LENGTH HANDLE  
The full-scale illustration above shows the panel  
and handle profile of a 130˚ door opening with  
2" (51) filler strip for framed applications.  
To obtain local dealer information, visit the  
Locator section of our website, subzero.com.  
The full-scale illustration on the following page  
lets you see what considerations you need to  
make for any overlay panel applications, and  
how they may interact with adjacent cabinets  
and/or countertops.  
Interference of door panels with handles at  
maximum door swing may require the use of an  
optional 90˚ door stop available through your  
Sub-Zero dealer.  
*Approximate thickness of wrapped  
stainless steel door.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
13  
 
Planning Information  
Built-In Model 601RG  
O V E R L AY PA N E L A P P L I C A T I O N  
9 0 ˚ D O O R O P E N I N G  
NOMINAL OVERALL  
WIDTH OF SUB-ZERO  
90˚ DOOR OPENING  
(TOP VIEW)  
SUB-ZERO UNIT  
7
23 /8" (606) TO REAR  
OF SUB-ZERO  
MAIN FRAME  
0" (0)  
/4" (6)  
1
DOOR CLOSED  
1
3
/2" (25)  
/4" (19)  
1" (25)  
HINGE  
1
1 /4" (32)  
1
1 /2" (38)  
3
1 /4" (44)  
2" (51)  
1
2 /4" (57)  
1
2 /2" (63)  
DOOR OPEN @ 90˚  
3
2 /4" (70)  
3" (76)  
1
3 /4" (83)  
1
3 /2" (89)  
OVERLAY PANEL  
3/4" (19) THICK (NOMINAL)  
*Approximate thickness of wrapped  
stainless steel door.  
Dimensions in parentheses are in  
millimeters unless otherwise specified.  
14  
 

Sharp CD Player IM DR420H User Manual
Sharp Computer Drive TM 20 User Manual
Sharp TV Mount PN ZK10 User Manual
Sony VCR HVR M25AU User Manual
Star Micronics Printer TUP900 User Manual
Sun Microsystems Switch 820 4733 10 User Manual
Sylvania CD Player SRCD243 User Manual
Sylvania CRT Television DCT1903R User Manual
Tanaka Chainsaw ECS 506 User Manual
Tandberg Data Cassette Player VXA 320 VXA 3 User Manual